It should be noted that the definition as written does not define the power of the motor in Watts as is conventionally done for electric bicycles but rather in brake horsepower. Thus for an electric bicycle, motor kit, or electric bicycle motor that is not rated by the manufacture in brake horsepower but rather in Watts a conversion must be made in the units a conversion which is not given in the code of the law and thus the court will have to consider a factor of conversion that is not directly encoded in the law. Industry standard conversion for Watts to horsepower for electric motors is 1 horsepower = 746 watts. Acceptance of that conversion factor from industry, however, as interpretation of the law is subject to the process of the courts since it is not defined specifically in the law.
In New Zealand, the regulations read: "AB (Power-assisted pedal cycle) A pedal cycle to which is attached one or more auxiliary propulsion motors having a combined maximum power output not exceeding 300 watts." This is explained by NZTA as "A power-assisted cycle is a cycle that has a motor of up to 300 watts. The law treats these as ordinary cycles rather than motorcycles. This means that it is not necessary to register or license them. Note that the phrase "maximum power output" that is found in the regulation (but omitted in the explanation) may create confusion because some e-bike motor manufacturers advertise and print on the motor their "maximum input power" because that number is larger (typically motors run at about 80% efficiency ) thus give the impression the buyer is getting a more powerful motor. This can cause misunderstandings with law enforcement officers who do not necessarily understand the difference, and when stopping a rider on an e-bike in a traffic stop, look at the number on the motor to determine if the e-bike is legal or not.
If you're more concerned with conquering the countryside than the commute, Cyclotricity's Stealth is the one for you. It's a full-size mountain bike, with aggressive tyres and suspension on the front forks to absorb the rocks and bumps on the trails. It's comfortable to ride, and its motor can either give you assistance while you ride, or you can just hit the throttle to rocket over hills with no effort on your part.
There are dozens of good 25Km/h pedelecs. Our advice is to go the nearest good e-bike store and get it from there, because e-bikes may need good support. Only if you like servicing a bike yourself is buying from the Internet a good option. As of Spring 2013, a good benchmark to compare with is the Austrian KTM Amparo also called KTM Severo 8M or the German Kalkhoff Impuls or Agattu series. It has a reliable Panasonic middle motor and a good battery. If you want a more sexy design, try the SMART from the urban car maker of the same name.
The definition was clearly written with gasoline-powered pedalcycles in mind. The requirement of an automatic transmission is troublesome for those who just want to add an electric-assist motor to a bicycle, for almost all bicycles have transmissions consisting of chains and manually shifted sprockets. The registration form asks for a VIN, making it difficult to register some foreign-made ebikes. The fine for riding an unregistered electric bike is approximately $160.00 per event as of 2007.
"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,  written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
I'm wondering if renter's insurance will cover my eBike while I'm out cycling around town to work, shopping, or even on long distance eBike tours ….. And what exactly will the insurance cover … only the bicycle …. all of the extra features …. gadgets … gear ….. This beast will cost me around $9,500.00 (US) when finished. At times I will be carrying as much as $3,000.00+ worth of gear !!!
A KS LEV Integra dropper post, 130mm of front and rear travel, 27.5-inch wheels, and trail-grabbing 2.8-inch tires make this pedal-assist mountain bike a great option if you want to climb farther to shred longer, but don’t want to lug your bike uphill for ages. The 250-watt motor, placed slightly farther forward than most other bikes to optimize weight distribution and handling, provides a nice boost so you can enjoy the ride up and not be too gassed when you get to the top.
Equipped with a powerful motor, a portable Li-ion Battery, and all the other magic that goes into building a LightSpeed Electric Bicycle… It’s lighter than it looks, strong yet agile, and feels like flying.This beast is truly larger than life. To bring it home, you need a special invite. Follow this space for more information on how to get invited.
The great majority of modern bicycles have a frame with upright seating that looks much like the first chain-driven bike. These upright bicycles almost always feature the diamond frame, a truss consisting of two triangles: the front triangle and the rear triangle. The front triangle consists of the head tube, top tube, down tube, and seat tube. The head tube contains the headset, the set of bearings that allows the fork to turn smoothly for steering and balance. The top tube connects the head tube to the seat tube at the top, and the down tube connects the head tube to the bottom bracket. The rear triangle consists of the seat tube and paired chain stays and seat stays. The chain stays run parallel to the chain, connecting the bottom bracket to the rear dropout, where the axle for the rear wheel is held. The seat stays connect the top of the seat tube (at or near the same point as the top tube) to the rear fork ends.
Unrelated to the show but also of local interest. The BC government is soliciting input on what is meant by "active transportation" which could hopefully help to direct policy and regulation governing not just ebikes but all kinds of human scaled transport. If you think electric skateboards should be on their radar or faster S-Pedalec class ebikes then this is a chance to have your voice heard. Electric bicycles have been an entirely grass roots phenomenon for most of their trajectory and it's encouraging to see the entire scope of personal mobility finally being acknowledged and discussed at this level.
Most consumers want an e-bike that will accommodate its motor without being too cumbersome and will remain stable in spite of its electronic components. Some consumers want only the most basic of e-bike features, including lights, a cargo rack/basket, and a water bottle holder. Others are focused more heavily on safety features, such as brake type. And still others are concerned with convenience and portability.
There are a variety of gadgets in the market for a hunter. These gadgets have made the hunting experience a lot easier and better. However, not everyone requires everything available in the market. It’s from your experience you learn what is best for you. Let’s look at some important gadgets you may want to have on your next hunting trip. Electric Hunting Bikes Electric hunting bikes are a better bet than the dirt bikes or ATV’s. It makes lesser noise than the other modes of transport so you don't spook the wildlife. You can carry your gadgets and hunting...
China's experience, as the leading e-bike world market, has raised concerns about road traffic safety and several cities have considered banning them from bicycle lanes. As the number of e-bikes increased and more powerful motors are used, capable of reaching up to 30 miles per hour (48 km/h), the number of traffic accidents have risen significantly in China. E-bike riders are more likely than a car driver to be killed or injured in a collision, and because e-bikers use conventional bicycle lanes they mix with slower-moving bicycles and pedestrians, increasing the risk of traffic collisions.
Many countries have enacted electric vehicle laws to regulate the use of electric bicycles. Countries such as the United States and Canada have federal regulations governing the safety requirements and standards of manufacture. Other countries like the signatories of the European Union have agreed to wider-ranging legislation covering use and safety of their term EPAC (electric vehicles)
In summary, federal law trumps all States’ laws. That is true with bicycle law, too. States cannot constitutionally pass legislation that reduces or eliminates Federal laws, they can only pass legislation that enacts additional (tighter) restrictions on its people. States can’t define an ebike a bicycle if greater than 750W/20mph, nor can they define an ebike a motor vehicle if less than the Federal Government’s limit of 750 Watts and a top electric-powered speed of 20 MPH.3This is the Federal definition of a low speed electric bike, which equates it to a bicycle.
Besides voltage, batteries are rated by amp hours (AH). Although voltage seems to get the most attention, the amp hour rating of the battery is just as important. It is the measure of a battery’s capacity and provides a good indication of the range you can expect from an electric bike. Although lots of factors come into play in determining range (ie: rider weight, terrain, input, efficiency, etc.), a good rule of thumb is range is equal to AH. So under normal conditions, an average rider can expect 10 miles out of a 10AH battery (with no pedaling). With rider input, this number can be dramatically increased, so most 10AH batteries are rated “up to 20 miles” by the manufacturer which assumes pedaling. On pedal-assist bikes (which require pedaling), the range ratings are much higher because the rider is constantly assisting the motor and reducing the current draw.
DIY Kit ebikes – Ebikes that are home built with a DIY kit, and exceed the 750W/20mph definition, are also allowed to be bought, build, and ridden. DIY kits are throttle activated. Some of the newer systems have PAS options. Ebike kits are not unilaterally prohibited or assigned motor vehicle status, but again, legal classification and road use falls under state law.
Electric bikes are becoming a convenient and fun way to commute around a city, but they can be pricey. The average e-bike can cost $3,000, with some models getting up to $5,000 or more. But these prices are dropping, as new models come onto the market — and if you don’t mind giving up some of the glossier, high-tech features like embedded digital displays, retractable cable locks, and and theft tracking and recovery, you can find a really good quality e-bike for under $1,500.
Great question… a real world situation from someone doing their best to follow the law but also be realistic about time/distance. What follows is my opinion on the matter based on lots of electric bike riding experience, this is not legal advice. You can probably ride with electric assist across the dirt way with no issues and avoid any negative response that might arise as long as you’re polite to other cyclists and pedestrians and pedal along without going too fast. If someone called you out about it you could easily hop off, walk your bike and explain that you use the assist to help make your commute possible or possibly, like me, you have a knee injury and it’s difficult to pedal through softer terrain like gravel. Another different approach might be to shut the bike off completely before entering the gravel section, you could even take the battery off and put it in a backpack or as mentioned earlier… just walk the bike. Imagine if you had a motorized dirt bike and were just pushing it along a sidewalk… this kind of vehicle definitely is not allowed on sidewalks or most gravel paths like the one you’re describing but if you were escorting it carefully, you’d be honoring the spirit of the law and if an officer or pedestrian jumped out and started questioning you about your “motorized vehicle” it is my feeling that a genuine explanation and apology or request for guidance would go very well. I personally have never had issues riding electric bikes in part because I am thoughtful about how I use them. I do occasionally switch them off and sometimes I get off and walk. I have asked police in many cities across the US what they thought about ebikes and in every case I have received positive interest and support with guidance to ride safe with a helmet and follow traffic laws in the street. I hope this helps and I wish you well, it’s nice that you care enough to ask and I hope you’re treated well by others out on the road. The flip side of this response is that I have been harassed, yelled at and even swerved at by automobiles when riding bicycles and electric bikes. This usually happens in the evening after work lets out when traffic is heavy and I’m riding on the shoulder or in the street (where marked to do so) and I believe it has to do with territory, testosterone and socio-economic standing more so than laws or anything like that.
"Bicycle" means either of the following: (1) A device having two wheels and having at least one saddle or seat for the use of a rider which is propelled by human power. (2) A device having two or three wheels with fully operable pedals and an electric motor of less than 750 watts (one horsepower), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden, is less than 20 miles per hour.
Maintenance of adequate tire inflation is the most frequent and troublesome concern for cyclists and many means and methods are employed to preserve pneumatic integrity. Thicker tires, thicker tubes, tire liners (of a number of rather impenetrable devices installed between the tire and tube), liquid sealing compounds squeezed into the tube, and automotive-style patch kits are all used to reliably contain the typical tire pressures of 40 to 60 pounds per square inch that are required for bicycle operation. Thin, light bicycle tires are particularly vulnerable to penetration and subsequent deflation caused by goat's heads and other burs, colloquially known as stickers. Inflation of bicycle tires to pressures higher than typical for automotive use requires special pumps. The complexity of bicycle tire maintenance and repair may cause many to not consider the bicycle for transport or leisure.
The Netherlands has a fleet of 18 million bicycles. E-bikes have reached a market share of 10% by 2009, as e-bikes sales quadrupled from 40,000 units to 153,000 between 2006 and 2009, and the electric-powered models represented 25% of the total bicycle sales revenue in that year. By early 2010 one in every eight bicycles sold in the country is electric-powered despite the fact that on average an e-bike is three times more expensive than a regular bicycle.
The Super Commuter is very aptly named. The 350w Bosch motor will help you sustain speeds of up to 28mph, and the burly, 2.4-inch wide, Schwalbe Super Moto-X 650b tires will keep you secure on even the roughest city streets, and Shimano Deore hydraulic brakes provide ample stopping power. Fenders provide welcome protection from road spray so you arrive at your destination fresh, integrated lights are critical for post-sunset riding, and a side-view mirror hanging on the left side of the handlebar gives a great view of traffic around you. After all, you can ride at the speed of urban traffic on the Super Commuter.
For years, riders have been making fun of others who mount mudguards, a rack and a fixed headlight on their bikes. Admittedly, these home-built creations usually aren’t very attractive, but there is a reason why many riders do it anyway. For them, their bike is more than just a piece of sports equipment or a status symbol. They use it in their day-to-day lives and for that, above all else, it has to be practical. Ever more manufacturers are catching on and offering complete, everyday eMTBs, which, compared to trekking bikes, are well suited for light off-road use too. On top of that, the wider tyres and longer travel of the new breed of SUV bikes offer additional safety in urban environments e.g. on kerbs, railway tracks or on wet, dirty roads. Oh, and they look really good too, as proven by the SCOTT Axis eRide we recently reviewed! The most prominent representative of this new breed is Haibike’s new FLYON series.
However, Emu sells a little foldable number if that's your bag. The Emu Crossbar is for town commuters that require a sweet ride that's backed up by solid Shimano Nexus hub gears and Tektro brakes, which are adequate if not the best on the market. Riding is smooth and easy, with the crank moving sensor doing its best to iron out any gaps in power delivery.
Bicycles and horse buggies were the two mainstays of private transportation just prior to the automobile, and the grading of smooth roads in the late 19th century was stimulated by the widespread advertising, production, and use of these devices. More than 1 billion bicycles have been manufactured worldwide as of the early 21st century. Bicycles are the most common vehicle of any kind in the world, and the most numerous model of any kind of vehicle, whether human-powered or motor vehicle, is the Chinese Flying Pigeon, with numbers exceeding 500 million. The next most numerous vehicle, the Honda Super Cub motorcycle, has more than 60 million units made, while most produced car, the Toyota Corolla, has reached 35 million and counting.
IZIP ebikes is currently holding their huge annual sale. We know that IZIP makes high quality electric bikes that you can buy and ride with confidence. The current sale is a clearance of their 2018 models. One of the best ways to get a good deal on any bike is to buy a previous year’s model. Plus, IZIP offers free same-day shipping. So we have highlighted two of the best bargains in ebikes available from IZIP right now.
Electric bikes advertise with a huge array of varying ranges, but what is the dominant factor is range? Electric bike range is determined by the battery, and just like other lithium battery products like laptops and cell phones the batteries performance can fluxuate based on a variety of external factors. Extreme cold, rider weight, head winds, hills, rough terrain, tire pressure and many other factors. But since we need to start somewhere to get the general range that a battery can produce there is baseline that we can reference to get a good indicator of range. Take a look at...
Earlier UK regulations required that the motor has an average power output limited to 200 W (250 W for tricycles and tandems) and weight limited to 40 kg (60 kg for tricycles and tandems). These regulations must come in-line with the EU regulations by (find deadline). For models sold before June 2003, e-bikes conforming to the speed, weight and power limits may also be considered pedal cycles. Electric bikes with higher power outputs, or those not meeting the "pedelec" definition are now treated as motorcycles and require a license.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.
You turn it on by pressing the green button on the battery once for low power and twice for high, although to be honest, there is not a lot of difference between them. After that, you just pedal. There are no gears, no chain to muck up your trousers (a motorbike-style carbon fibre belt is used instead) and not that much difference in feeling compared to riding a normal bike.
Would an e-bike that used a trailing generator to power the electric motor still be considered an e-bike? The purpose of the generator is allow greater distances to be traveled and all day riding. The gen-set that I am looking at uses a 49 cc gas engine with a 12 volt generator, this would be from the ground up build using a 1 hp electric motor. This seems to stay within the state laws of AZ. where I reside. Thanks for your thoughts.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.