"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[142]
The U.S. Consumer Product Safety Act states that electric bicycles and tricycles meeting the definition of low-speed electric bicycles will be considered consumer products. The Consumer Product Safety Commission (CPSC) has regulatory authority to assure, through guidelines and standards, that the public will be protected from unreasonable risks of injury or death associated with the use of electric bicycles.[61][62]
It appears Tennessee has not passed any legislation that applies to electric bicycles. Some people think the laws pertaining to a Motorized Bicycle should be used for an electric bicycle. However, a Motorized bicycle would be a gasoline powered device per state law as it is defined as "means a vehicle with two (2) or three (3) wheels, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters (50cc) which produces no more than two (2) brake horsepower and is capable of propelling the vehicle at a maximum design speed of no more than thirty miles per hour (30 mph) on level ground." [56]
Can I legally buy/build and ride an ebike that’s faster than 20 mph? Yes you can, but you need to know that the ebike is no longer considered equivalent to a bicycle and is subject to other state vehicular classifications. The definitions for electric bikes spanning 20-30mph, and 1-2 horsepower ranges, will vary from state to state, resulting in a no-man’s-land consensus about limits for motor vehicle definition. The common label for a 20-30mph, 2-wheeled vehicle with active pedals is a Moped. Other MVA labels include motor scooter, motorbike and dirt bike which may have equivalent power and speed performance, but do not have pedals to assist and move the vehicle.
Perhaps the cleverest thing of all about the Electric Brompton is that despite all the extra stuff, it folds up exactly the same as the non-powered variety. It's so simple, and unlike certain folding bikes we could mention, what you're left with is a genuinely small thing, rather than something that's about the size of a bike with the front wheel taken off.
Included in this shipment are the much awaited 3540 motors with their slick "UFO" design. These are the replacements for the older square style "H" motors, you may have noticed that this change was implemented last year with the 3525 front and rear motors. As always, we have the motors customized with a 10K NTC thermistor for thermal rollback using the CA3.
For a more stylish ride, cast your eyes over the Coboc Rome. It's a full-size bike, with gorgeous stylings, and large wheels that let you pick up plenty of speed on the road. It has a fuss-free approach too, with its automatic motor assistance -- all you need to do is get on and ride. It's very much like any fixed gear bike you'll see on the streets, but with the additional motor, it's less effort to get about.
E-bikes use rechargeable batteries and the lighter ones can travel up to 25 to 32 km/h (16 to 20 mph), depending on local laws, while the more high-powered varieties can often do in excess of 45 km/h (28 mph). In some markets, such as Germany as of 2013, they are gaining in popularity and taking some market share away from conventional bicycles,[1] while in others, such as China as of 2010, they are replacing fossil fuel-powered mopeds and small motorcycles.[2][3]
E-bikes are classed according to the power that their electric motor can deliver and the control system, i.e., when and how the power from the motor is applied. Also the classification of e-bikes is complicated as much of the definition is due to legal reasons of what constitutes a bicycle and what constitutes a moped or motorcycle. As such, the classification of these e-bikes varies greatly across countries and local jurisdictions.
The environmental effects involved in recharging the batteries can of course be reduced. The small size of the battery pack on an e-bike, relative to the larger pack used in an electric car, makes them very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots", in which e-bike riders can charge their vehicles while parked under photovoltaic panels.[66]
GPS Firmware: This net update will be much appreciated by people who have a GPS Analogger device with their CA3. With a simple hardware modification to the Analogger circuit, the GPS data will be transmitted from your existing TRS cable back to the Cycle Analyst. You can then see the time of day, your elevation, position, and direction all on the CA3 screen. The firmware also features additional custom views on the main screen, allowing you to replace or toggle the battery voltage with any of these new parameters to get just the display you are after.

Maintenance of adequate tire inflation is the most frequent and troublesome concern for cyclists and many means and methods are employed to preserve pneumatic integrity. Thicker tires, thicker tubes, tire liners (of a number of rather impenetrable devices installed between the tire and tube), liquid sealing compounds squeezed into the tube, and automotive-style patch kits are all used to reliably contain the typical tire pressures of 40 to 60 pounds per square inch that are required for bicycle operation. Thin, light bicycle tires are particularly vulnerable to penetration and subsequent deflation caused by goat's heads and other burs, colloquially known as stickers. Inflation of bicycle tires to pressures higher than typical for automotive use requires special pumps. The complexity of bicycle tire maintenance and repair may cause many to not consider the bicycle for transport or leisure.
Bicycle suspensions are used primarily on mountain bicycles, but are also common on hybrid bicycles, as they can help deal with problematic vibration from poor surfaces. Suspension is especially important on recumbent bicycles, since while an upright bicycle rider can stand on the pedals to achieve some of the benefits of suspension, a recumbent rider cannot.

It should be noted that the definition as written does not define the power of the motor in Watts as is conventionally done for electric bicycles but rather in brake horsepower. Thus for an electric bicycle, motor kit, or electric bicycle motor that is not rated by the manufacture in brake horsepower but rather in Watts a conversion must be made in the units a conversion which is not given in the code of the law and thus the court will have to consider a factor of conversion that is not directly encoded in the law. Industry standard conversion for Watts to horsepower for electric motors is 1 horsepower = 746 watts.[105] Acceptance of that conversion factor from industry, however, as interpretation of the law is subject to the process of the courts since it is not defined specifically in the law.
(2) BICYCLE.--Every vehicle propelled solely by human power, and every motorized bicycle propelled by a combination of human power and an electric helper motor capable of propelling the vehicle at a speed of not more than 20 miles per hour on level ground upon which any person may ride, having two tandem wheels, and including any device generally recognized as a bicycle though equipped with two front or two rear wheels. The term does not include such a vehicle with a seat height of no more than 25 inches from the ground when the seat is adjusted to its highest position or a scooter or similar device. No person under the age of 16 may operate or ride upon a motorized bicycle.
Attitudes to electric bikes have changed in recent years. For a long time they were seen by cyclists as 'cheating' and by non-cyclists as being just like a bike, but uglier and far more expensive. This new breed of best-in-class electric bikes feel more natural, look more normal, and people are coming around to the idea that a ride with the convenience of a bike but without all the sweat and effort is a Very Good Thing. 

At the moment this battery is in stock but for local pickup orders only as we are going through the certification testing required for shipping. We've been keeping the 21700 cell offerings on our radar as they start to catch up with the performance specs of the more mature 18650 series and this year it looks like they are finally making the grade. Expect more from us as the year goes on. 


Oregon Law (ORS 801.258]) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed greater than 20 miles per hour on level ground.[124]
The Class 3 Aventon Pace 500 urban e-bike has five levels of pedal assist and tops out at 28 mph. But the Pace has something not found on a lot of modern e-bikes. In addition to pedal power, it also has a throttle—in the case of the Pace, a small thumb paddle on the left side of the handlebar next to the control unit that holds at a steady 20 mph, no pedaling required. The bike itself has an aluminum frame, a swept-back handlebar, ergo grips, a sturdy kickstand, hydraulic disc brakes, 8-speed Shimano Altus shifting and gearing, 27.5x2.2-inch Kenda e-bike-rated tires, a saddle the size of Texas, and good ol’ classic city/commuter-bike geometry. It doesn’t come equipped with fenders or a rear rack, but you can add them. Power comes in the form of a 500-watt rear-hub motor, a semi-integrated battery on the down tube (with a range of up to 50 miles), and a backlit display unit mounted on the stem.
The Tidalforce Electric Bicycle was an electric bicycle manufactured by Wavecrest Labs from 2003 until the company went out of business in 2006. All models of Wavecrest Tidalforce electric bikes have a 36 volt electric hub motor built into the rear wheel hub and a 36 volt battery pack built into the front wheel hub. Wavecrest Labs manufactured three models of Tidalforce bikes: The Wavecrest Tidalforce M-750, the S-750 Traditional hard tail mountain bike and the iO-750 Cruiser. Any of the three bikes with an X suffix denotes that the motor is a 1000 watt motor without a set speed restriction as compared to the speed limited 750 watt version.
This is one of the most incredible eBikes on the market today! The Riese and Muller SuperCharger Rohloff GX is one of our most popular models and we know they are being put through thousands of miles across the Southeast. From the coastal areas to the Appalachian mountains, we have customers buying and riding these highly engineered eBikes. These eBikes …
Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
Since 2001, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs). They are currently defined as a two or three wheeled bicycle with an attached electric motor of 500W or less and which is capable of being propelled manually. Furthermore to meet the safety requirements set down by this legislation it must meet the following; when engaged by muscular power it must cease assistance when muscular power ceases or if powered by an accelerator controller cease power when braking and be incapable of providing assistance above 32 km/h and bear a label that is permanently affixed by the manufacturer and appears in a conspicuous location stating the vehicle is a power-assisted bicycle.[5][6]
Justin and Anne-Sophie have been on the road in Europe for about a week now, catching as much sun as they can on the Suntrip. Since the start of the trip in Lyon and the official start of the race in Chamonix, they have been trending on a more southerly route towards Turkey and Iran. As they get used to the style of travel and the nuances of riding a three-wheeled solar vehicle all day they have had their ups...
Another style is the recumbent bicycle. These are inherently more aerodynamic than upright versions, as the rider may lean back onto a support and operate pedals that are on about the same level as the seat. The world's fastest bicycle is a recumbent bicycle but this type was banned from competition in 1934 by the Union Cycliste Internationale.[43]
The bicycle's invention has had an enormous effect on society, both in terms of culture and of advancing modern industrial methods. Several components that eventually played a key role in the development of the automobile were initially invented for use in the bicycle, including ball bearings, pneumatic tires, chain-driven sprockets and tension-spoked wheels.[10]
I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have
The two most common electric motor styles used in today’s e-bikes are hub motors and mid-drive motors. The Freedom uses a hub motor, which was located in the center of the rear wheel. Hub motors typically don’t offer the same natural maneuverability as the increasingly more common (and more expensive) mid-drive motors because their weight is concentrated in the rear of the bike. It can be jarring when the motor prevents you from going faster than the allotted speed, especially when cruising downhill, but 20 mph is the legal maximum for e-bikes in the US. (In the EU, it’s even lower: 25 km/h, or 15.5 mph.)

Electric motor assisted bicycles have been banned in the State of New York and are not permitted for on-road use.[50][51] It appears the only known allowance of an electric bicycle is if it is an electric powered moped, at this time. There is a proposed bill to allow ebikes. As of May 2009, Bill A2393("Defines the term electric assisted bicycle") has been passed in the NY State Assembly[52] and its corresponding Bill S4014, sponsored by Senator Thomas Morahan, is before the NY State Senate.[53]
Motor position – e-bike motors are positioned on either the front wheel hub, rear wheel hub, or in the middle of the bike between the pedals. There are pros and cons of each, but we think the mid-engine motor gives better weight distribution and the most natural bike riding feel. The pulling sensation you get from a front hub motor in particular can feel a bit unnatural

(ii) a vehicle equipped with two or three wheels, foot pedals to permit muscular propulsion, and an independent power source providing a maximum of 2 brake horsepower. If a combustion engine is used, the maximum piston or rotor displacement may not exceed 3.05 cubic inches, 50 centimeters, regardless of the number of chambers in the power source. The power source may not be capable of propelling the device, unassisted, at a speed exceeding 30 miles an hour, 48.28 kilometers an hour, on a level surface. The device must be equipped with a power drive system that functions directly or automatically only and does not require clutching or shifting by the operator after the drive system is engaged.
Maybe the most confusing legal issue facing e-bike riders today is the difference between a bike lane and bike path. A bike lane is a marked section of roadway shared with motor vehicles. Bike paths pretty much universally prohibit the use of motorized vehicles. Still, you will need to research your area. As an example: “A path near our office specifically says “no motorized bicycles.” Yet, when we tracked down an employee who claimed to work enforcement on the path, he said that our e-bike was allowed.”8

Hmm, that’s unfortunate. I actually have a doctors note that I carry along which recommends the use of an assisted bicycle. I ride thoughtfully and have never been asked to show it. I cannot comment on the federal parks, perhaps they are not aware of the federal law classifying electric assist bikes that perform at or below 20 mph and 750 watts as bicycles. Having a note and this information would be a good response if you were questioned.
Unrelated to the show but also of local interest. The BC government is soliciting input on what is meant by "active transportation" which could hopefully help to direct policy and regulation governing not just ebikes but all kinds of human scaled transport. If you think electric skateboards should be on their radar or faster S-Pedalec class ebikes then this is a chance to have your voice heard. Electric bicycles have been an entirely grass roots phenomenon for most of their trajectory and it's encouraging to see the entire scope of personal mobility finally being acknowledged and discussed at this level.
This is list of the best performing, best value electric bikes for 2018 / 2019. For each category I list two models, the first recommendation is based on performance and the second is based on affordability. As you explore the list and get to know EBR, check out the ebike community forum for more personalized feedback. Share your height, weight, budget and intended use (along with bikes you like) to get advice from actual owners and moderators.

The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885.[7][8][9] However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
×