Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.
In most jurisdictions, bicycles must have functioning front and rear lights when ridden after dark. As some generator or dynamo-driven lamps only operate while moving, rear reflectors are frequently also mandatory. Since a moving bicycle makes little noise, some countries insist that bicycles have a warning bell for use when approaching pedestrians, equestrians, and other cyclists, though sometimes a car horn can be used when a 12 volt battery is available.[citation needed]
Tires vary enormously depending on their intended purpose. Road bicycles use tires 18 to 25 millimeters wide, most often completely smooth, or slick, and inflated to high pressure in order to roll fast on smooth surfaces. Off-road tires are usually between 38 and 64 mm (1.5 and 2.5 in) wide, and have treads for gripping in muddy conditions or metal studs for ice.

Vehicles with an electric power and power of less than 300W are classified as "not a motor vehicle". Such electric bicycles must comply with the same rules as bicycles. You must wear a helmet even on a scooter or bike under 300W. If the power is over 300W or a combustion engine is used it is a "low powered vehicle" and the moped rules apply. Specifically, a drivers license and registration are required.
While the first functional battery was developed in the year 1800 by Italian physicist Alessandro Volta, a practical battery would not be seen for several decades yet. By the end of the 19th century, practical and portable batteries were more widely available, this finally freeing the electric motor to be used in a wide new array of applications. It might come as a surprise, but the electric motor, battery, and a bicycle were first paired as far back as the 1890s. It would be approximately 100 years later that electric bicycle development finally entered the mainstream, but the technology and concept behind the electric bike were all in place generations ago.
Despite the illegal status in the state of New York, enforcement of this law varies at the local level. New York City enforces the bike ban with fines and vehicle confiscation for throttle activated electric bikes.[113] However, Mayor Bill de Blasio has recently changed the city's official policy to legalize pedal-assist electric bikes that have a maximum speed limited to 20 mph. [114] Contrarily, Tompkins County supports electric bike usage, even providing grant money to fund electric bike share/rental projects.[115]
The environmental effects involved in recharging the batteries can of course be reduced. The small size of the battery pack on an e-bike, relative to the larger pack used in an electric car, makes them very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots", in which e-bike riders can charge their vehicles while parked under photovoltaic panels.[66] 

Battery-electric locomotive Battery electric vehicle Cater MetroTrolley Electric aircraft Electric bicycle Pedelec Electric boat Electric bus Battery electric bus Electric car List Electric truck Electric platform truck Electric vehicle Electric motorcycles and scooters Electric kick scooter Gyro flywheel locomotive Hybrid electric vehicle Hybrid train Motorized bicycle Neighborhood Electric Vehicle Plug-in electric vehicle List Plug-in hybrid electric vehicle Solar vehicle Solar car Solar bus
Did you know that electric bikes can be used for fitness training? Or that they have been scientifically proven to increase the amount of cycling people do? Or that they have proven health and fitness benefits? Well, it’s all true! Apart from being tons of fun, ebikes can be used to improve health and fitness in many ways. Here are our top posts about how ebikes can improve your health and fitness.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
By Max Shumpert: This article has been updated to reflect the most accurate information regarding best e-bikes available for those who are interested in new technology combined with traditional bikes. The best 5 available have changed, and information has been added to assist individuals in finding the best electric bicycles currently available on the market. The FAQ has also been updated.

In the 1890s, electric bicycles were documented within various U.S. patents. For example, on 31 December 1895, Ogden Bolton Jr. was granted U.S. Patent 552,271 for a battery-powered bicycle with "6-pole brush-and-commutator direct current (DC) hub motor mounted in the rear wheel". There were no gears and the motor could draw up to 100 amperes (A) from a 10-volt battery.[5]
Besides voltage, batteries are rated by amp hours (AH). Although voltage seems to get the most attention, the amp hour rating of the battery is just as important. It is the measure of a battery’s capacity and provides a good indication of the range you can expect from an electric bike. Although lots of factors come into play in determining range (ie: rider weight, terrain, input, efficiency, etc.), a good rule of thumb is range is equal to AH. So under normal conditions, an average rider can expect 10 miles out of a 10AH battery (with no pedaling). With rider input, this number can be dramatically increased, so most 10AH batteries are rated “up to 20 miles” by the manufacturer which assumes pedaling. On pedal-assist bikes (which require pedaling), the range ratings are much higher because the rider is constantly assisting the motor and reducing the current draw.
The rest of the bike is equally impressive. Integrated lights in the front and the rear run directly off the main battery, so you’re never replacing coin cells or AAA batteries. And the disc brakes give you plenty of stopping power. The 36-volt battery attaches to the down tube and is designed to be easily removed for recharging. A key-lock at the top of the mount ensures that no one can steal your battery if your bike is left in a public place. And a built-in alarm system, activated with a car-like key fob, is ear-splitting enough to keep thieves away altogether. (Miller promises the alarm’s sensitivity is tuned so it shouldn’t go off if the bike is jostled at a public bike rack, but I didn’t have the bike long enough to test this out.)
Electric-assisted bicycle operators must follow the same traffic laws as operators of motor vehicles (except those that by their nature would not be relevant). The bicycles may be operated two abreast. Operators must generally ride as close as is practical to the right-hand side of the road (exceptions include when overtaking another vehicle, preparing for a left turn, and to avoid unsafe conditions). The bicycle must be ridden within a single lane. Travel on the shoulder of a road must be in the same direction as the direction of adjacent traffic.
State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.

We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.
Because I am in an area with quite a lot of hills and steep inclines, some very steep, and the motor on the bike handles these hills effortlessly along with pedal assist. I will say I am not fit in anyway and there is no way I would have got up half of the hills I got up if it were not for the 250 watt motor on this bike, the low , medium and high pedal assist options are great and it is easy to assess which option you'll need depending on the hill.The battery was a lot heavier than I expected when holding it, feels like holiding a 3 LTR bottle of coca cola but I can forgive that

We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.


The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.
Bosch eBike Systems – eBikes 101 What is an eBike? The eBike is one of the most agile, comfortable vehicles of our time. With the positive impacts on health, environment and society, electric bikes bring a new meaning to smart mobility. Their modern components and simple yet innovative design allow for a variety of eBiking adventures, from trekking through the …
Thanks for reading the fine print. About the Wiki: We don't accept sponsorships, free goods, samples, promotional products, or other benefits from any of the product brands featured on this page, except in cases where those brands are manufactured by the retailer to which we are linking. For our full ranking methodology, please read about us, linked below. The Wiki is a participant in associate programs from Amazon, Walmart, Ebay, Target, and others, and may earn advertising fees when you use our links to these websites. These fees will not increase your purchase price, which will be the same as any direct visitor to the merchant’s website. If you believe that your product should be included in this review, you may contact us, but we cannot guarantee a response, even if you send us flowers.
X-Treme is a very well-known distributor of electric scooters and electric bikes with really great customer service. They offer a number of great budget electric bikes, and one of them is Catalina Beach Cruiser. Powered by 500W rear hub motor, this e-bike can conquer almost any terrain. The frame of this bike is 100% hand-welded aluminum, with a step-though design. The top speed on this bike is about 20 mph, with the range of up to 60 miles on pedal-assist mode. The battery pack is 48V LiPo4. This e-bike is an absolute joy to ride. Even more now, with an all new zero resistance rear hub motor with an automatic clutch. This makes riding without power a breeze and you will feel no resistance from the motor. Seat is large and very comfortable, with dual springs for smooth ride. It also comes with a basket, which is a must have if you plan on going for groceries or running errands on this bike.
It’s unlikely the Instagram generation ever thought there would be an eBike built with them in mind. Stereotypes of old people riding their e-assisted bikes with cumbersome batteries and questionable frames. Then Lithium Cycles and the Super 73 turned up! Across the last few months, social media has been bustling with talk, influencers, Will Smith … Continue reading Lithium Cycles Super 73: Coming Soon
Photo: Could solar power be the future of electric bicycles? The large solar panel mounted over the back wheel of this experimental bike powers an electric motor connected by a chain drive to the back wheel, helping the rider when he doesn't feel like pedaling. Using clean, green solar power would remove the problem of having to charge electric bikes with electricity generated from fossil fuels—and help to extend their range significantly. Photo by Warren Gretz courtesy of US DOE/NREL.
Rose Heyer and Josie Tabor of Dept Tech, Department of State Information Center, the Secretary of State and the office of ROCK AND BORGELT, P.C., Attorneys at Law, 24500 FORD ROAD, SUITE 10 DEARBORN HEIGHTS, MI 48127-3106, determined electric bicycles are considered mopeds and need registered and licensed. In order to operate an electric bicycle on public streets, the driver must have a valid operator, chauffeur, or special moped license. However, not all electric bicycles are street legal unless they have the following safety equipment: operating brake light, headlight, and turn signals. The local police department must inspect the bicycle using Form TR-54 which is taken with proof of purchase to the DMV. The fee for the plate is $15 for a three year decal, whereas the fine for no decal is $150 per incident.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24]. 

Controllers for brushed motors: Brushed motors are also used in e-bikes but are becoming less common due to their intrinsic lower efficiency. Controllers for brushed motors however are much simpler and cheaper due to the fact they don't require hall sensor feedback and are typically designed to be open-loop controllers. Some controllers can handle multiple voltages.
But electric bicycles—e-bikes—are new territory for me. Broadly speaking, there are two basic options in e-bike land: power-on-demand and pedal-assist. With the former, the rider can control the speed with a throttle instead of just pedaling. Think moped but with an electric motor instead of internal combustion. Pedal-assist, by contrast, requires the rider to do some of the work. The electric motor won't engage unless the rider is pedaling.
Your local state may have very definite rules as to what is an e-bike, what is a moped, and what is a motorcycle. While ebikes enthusiast don’t want the motor vehicle label, it is certain that each state will define some power level and speed where that classification will apply. Your best source of information is to go directly to your state motor vehicle department website, and get a copy of the your local state vehicle codes, with NO EDITING. Only recently updated official state vehicle codes will contain all the latest changes to the laws.1 For a link to your state MVA, look here:2 http://eco-wheelz.com/electric-bike-laws.php
Another style is the recumbent bicycle. These are inherently more aerodynamic than upright versions, as the rider may lean back onto a support and operate pedals that are on about the same level as the seat. The world's fastest bicycle is a recumbent bicycle but this type was banned from competition in 1934 by the Union Cycliste Internationale.[43]
There are a variety of gadgets in the market for a hunter. These gadgets have made the hunting experience a lot easier and better. However, not everyone requires everything available in the market. It’s from your experience you learn what is best for you. Let’s look at some important gadgets you may want to have on your next hunting trip.   Electric Hunting Bikes Electric hunting bikes are a better bet than the dirt bikes or ATV’s. It makes lesser noise than the other modes of transport so you don't spook the wildlife. You can carry your gadgets and hunting...
October 5, 2009 — Ontario is bringing in some new safety requirements for electric bikes. E-bikes, which can reach a speed of 32 kilometres per hour, are allowed to share the road with cars, pedestrians and other traffic throughout the province. The new rules limit the maximum weight of an e-bike to 120 kilograms, require a maximum braking distance of nine metres and prohibit any modifications to the bike's motor that would create speeds greater than 32 kilometres per hour. Also, riders must be at least 16 years of age, wear approved bicycle or motorcycle helmets and follow the same traffic laws as bicyclists. Municipalities will be able to decide where e-bikes may be used on their streets, bike lanes and trails. E-bikes will not be permitted on 400-series highways, expressways or other areas where bicycles are not allowed. Riding an e-bike under the age of 16 or riding an e-bike without an approved helmet carries fines ranging from $60 to $500. For all other traffic offences, e-bike riders will be subject to the same penalties as cyclists.
Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.

In my research about ebikes and the law, I cannot begin to justify how often articles about the laws evolved into the various ways and techniques to sneak around public notice and be stealth with the your ebike. The goal is to ride fast and fun, stay away from public awareness, and ‘Fly under the Radar’. I have been there and I get the drift. Sales and production are up. Electric bike kits, DIY enthusiast, long distance commuters, and a general drive for value is raising the desire for more options for consumers, wanting speed for fun and function, while developing amnesia for the law. People want to ride their new ebikes, and have the same access to safe pathways as they did the week before on their 100% human bike. Rather than deal with the inevitable conflicts over access, behavior and perception within the general public, the typical user will try to blend in with the normal cycling community.

Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.[5]
This year was busy at Haibike’s EUROBIKE stand. The reason: the new FLYON series, which we could only admire behind glass. The new bikes are the spearhead of Haibike’s eMTB development with an exciting and unprecedented level of integration and connectivity. They have a specially developed display, their own remote and, thanks to a 5,000 lumen headlight, are able to turn night into day. To make the rider visible at all times, taillights are neatly integrated into the frame. The bikes also come with the most powerful motor currently available on the market, from TQ Systems. We are sure that many will buy this bike not only for its performance but also as a status symbol.
During nighttime operation, the bicycle must be equipped with a front headlamp, a rear-facing red reflector, and reflectors on the front and rear of pedals, and the bicycle or rider must have reflective surfaces on each side. Minn. Stat. §169.222, subd. 6. An electric-assisted bicycle can be equipped with a front-facing headlamp that emits a flashing white light, a rear-facing lamp that has a flashing red light, or both. The bicycle can carry studded tires designed for traction (such as in snowy or icy conditions).

Most electric bicycles can be locked using keys supplied by the manufacturer. The key is usually inserted into a switch, which is commonly found on the bicycle's handlebars or on one side of the motor compartment. When switched to the "Off" position, the electrical drive system cannot be turned on. In areas of high risk for bicycle theft, these locking mechanisms are used in conjunction with coil or U locks.
By 1898 a rear-wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel, was patented by Mathew J. Steffens. Also, the 1899 U.S. Patent 627,066 by John Schnepf depicted a rear-wheel friction “roller-wheel” style drive electric bicycle.[7] Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his U.S. Patent 3,431,994. Wood’s device used 4 fractional horsepower motors; connected through a series of gears.[8]
What's the Centros like? Big and heavy, but with enough power to overcome that, it really reminded me of a more upmarket Volt Pulse. You do tend to find that the weightier e-bikes give more of a feeling of speed, even though you're only doing 20mph or so at the absolute most (only up to 15mph with electrical assistance so you'll need leg muscles or a downward incline to get to that outlandish velocity).
Solar Shunt firmware: With this firmware the Cycle Analyst can use the auxilliary input as a second current sensor for measuring and showing the solar amps and watts. You can not only see in realtime how much solar power is coming into the pack, you also get combined statistics such as the %solar recharge and the net wh/km mileage taking into account the solar input for the day. This is the ideal instrument for looking at solar ebike performance, consolodating all measurements in a single device.
At 42 pounds for a size medium frame (exceptionally light for an urban e-bike), this step-through model’s silent, mid-drive Bosch Active Line motor provides pedal assist up to 20 mph. And its 400Wh battery lasts a claimed 30 to a whopping 110 miles, depending on mode, speed, terrain, rider weight, cargo—all the usual stuff. With 26-inch wheels, 2-inch tires, round aluminum tubes, a swept-back handlebar, Shimano Sora 9-speed components, and an 11-32 cassette, the Parkway looks like an everyday, non-motorized city bike at first glance. But with an array of Bosch e-components—motor, battery, and Purion display—it has the zip to take you farther faster.

FuroSystems is a London-based startup that is launching two new full carbon fiber electric bikes, a folding e-bike and a mountain e-bike. FuroSystems’ ambition was to design very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and to sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.
As the managing editor of Ars Technica, one of my duties is to monitor the daily torrent of news tips and PR emails. The overwhelming majority of them is deleted after a glance, and the news tips and story ideas are passed along to the appropriate writer. Sometimes a product announcement will catch my eye, and I will follow up. Once in a blue moon, I'll say, "please send me one so that I may review it." And that's how I ended up riding an electric bike around the Chicago suburbs for two weeks.
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.
The Registrar will permit an electric motor driven cycle to be registered if it meets Canada Motor Vehicle Safety Standards (CMVSS) as a Limited Speed Motorcycle, or Scooter as is done with gas powered motor driven cycles. If the vehicle was manufactured after 1988 it will bear a compliance label stating that it meets these standards. The operator will be subject to all the requirements placed on operators of motor driven cycles.

There is a lot of information on the internet about electric bikes. Hopefully you have found lots of useful information right here, on this website. Based on this information, you may already have a preference for a specific electric bicycle and / or (technical) components. Your friends that ride e-bikes can also advise you based on their own experiences. But there is only one way you will know if you really make the right choice: take a test drive. During a test drive you will discover how close the riding experience is to your expectations.
Parliament has decided to approve the speed pedelec – a type of super electric bike that can reach speeds of up to 45 km/hour – for riding on cycle paths. Danish Parliament has decided that as of July 1 2018 those operating the super bikes only need to have turned 15 and wear a helmet, while the licence and number-plate demands will no longer be in play. [38]
×