Under the Guide Section of EBR, Court has written a full article, dedicated to the new classification approach, which was initiated by the BPSA (Bicycle Product Suppliers Association), supported by PeopleForBikes, and then Calbikes. The initiative was meant to be pro-active with ebike legislation, to establish self-imposed, measurable, distinct classes of electric bikes before states start hearing about anecdotal problems and potentially overreact to the technology with wide sweeping limitations.
However, laws and terminology are diverse. Some countries have national regulations but leave the legality of road use for states and provinces to decide. Municipal laws and restrictions add further complications. Systems of classification and nomenclature also vary. Jurisdictions may address "power-assisted bicycle" (Canada) or "power-assisted cycle" (United Kingdom) or "electric pedal-assisted cycles" (European Union) or simply "electric bicycles". Some classify pedelecs as distinct from other bikes using electric power. Thus, the same hardware may be subject to many different classifications and regulations.
By 1898 a rear-wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel, was patented by Mathew J. Steffens. Also, the 1899 U.S. Patent 627,066 by John Schnepf depicted a rear-wheel friction “roller-wheel” style drive electric bicycle. Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his U.S. Patent 3,431,994. Wood’s device used 4 fractional horsepower motors; connected through a series of gears.
For many bikes, battery range is more important than total power (because they’re all pretty powerful). You want a bike that delivers a range long enough for your rides at the power levels you want. Most e-bikes will have three to five levels of assist that kick in anywhere from 25 percent of your pedal power to 200 percent. Consider how fast the battery takes to recharge, especially if you’ll be using your bike for long commutes.
Beginning January 1, 2017, manufacturers and distributors of electric bicycles will be required to apply a label that is permanently affixed, in a prominent location, to each electric bicycle, indicating its class. Should a user "tamper with or modify" an electric bicycle, changing the speed capability, they must replace the label indicating the classification.
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle(they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.
Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.
Stöckli E.T. Urban Confort, made in Switzerland. It has SwissGoDrive motors and Samsung batteries. There is a 500W/17.6Ah combo that seems to be ideal for commuters, i.e. it has a 50km range using full assistance. In the USA, a similar product is available as Currie eFlow e3 Nitro (different motor and electronics). This model doesn't have a front wheel suspension, but comes with "balloon" tires that somewhat absorb shocks. Options are available through types: "simple"/Urban/CROSS and man/confort models. E.g. the Cross model has a front suspension, a 500W motor and no equipment like lights, fenders, etc. However, paying extra, you can compose your own configuration. If you commute using bumpy roads, then get a front suspension.
Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.
Firstly there's a magnetically-fired locking pin in the rear wheel, triggered by kicking a button on the hub. This is fairly secure in itself and almost impossible to remove without destroying the bike. In London, we'd pair it with a more traditional bike lock so there's a more obvious visual deterrent, though a LED matrix screen on the frame does issue a warning to would-be tea-leafs.
Bicycles featuring pedal power were developed during the subsequent decades of the 19th century, with the most emblematic example being the bicycle we know today as the Penny-Farthing. The bike was named based on the substantial difference in its wheel size resembling the larger and smaller Penny and Farthing coins, respectively. These bicycles were wildly popular among the well heeled upper classes of Europe and America despite their penchant for launching riders head first over the large wheel, not to mention their relative difficulty to mount and dismount.
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
The legal definition/description of an electric bicycle is most closely described in the code as a "motorized scooter" in that it is powered by an electric motor and/or human power . It may be also be described as a "Motorized bicycle". However, that description does not include electric powered motor specifically. And it appears that the legal definition "Motorized Bicycle" and "Motorized Scooter" are in conflict. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. A motorized bicycle shall not be operated upon any way, as defined in section one within the commonwealth by any person under sixteen years of age, nor at a speed in excess of twenty-five miles per hour. A motorized bicycle shall not be operated on any way by any person not possessing a valid driver’s license or learner’s permit. Every person operating a motorized bicycle upon a way shall have the right to use all public ways in the commonwealth except limited access or express state highways where signs specifically prohibiting bicycles have been posted, and shall be subject to the traffic laws and regulations of the commonwealth and the regulations contained in this section, except that the motorized bicycle operator may keep to the right when passing a motor vehicle which is moving in the travel lane of the way, and the motorized bicycle operator shall signal by either hand his intention to stop or turn. Motorized bicycles may be operated on bicycle lanes adjacent to the various ways, but shall be excluded from off-street recreational bicycle paths. Every person operating a motorized bicycle or riding as a passenger on a motorized bicycle shall wear protective headgear conforming with such minimum standards of construction and performance as the registrar may prescribe, and no person operating a motorized bicycle shall permit any other person to ride a passenger on such motorized bicycle unless such passenger is wearing such protective headgear.
Speed Pedelec ebikes – A new classification of bikes called ‘Speed Pedelecs’ have emerged which technically meet the bicycle definition for a 20 mph ebike. These ebikes are designed to max out at 28 mph. Pedelecs are pedal activated vs throttle activated. The weasel words within the definition says, “20mph on motor alone”. Thus, a person who adds their leg power to the motor assist and happens to cruise at 28mph is NOT doing it by motor alone, and therefore the bike is considered to be compliant with the Federal Law. If the rider stops pedaling, the speed pedelec cannot maintain speed. Speed Pedelecs are becoming more popular in Europe and America, which means more models are being offered.
"Bicycle" means either of the following: (1) A device having two wheels and having at least one saddle or seat for the use of a rider which is propelled by human power. (2) A device having two or three wheels with fully operable pedals and an electric motor of less than 750 watts (one horsepower), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden, is less than 20 miles per hour.,
This slick-looking commuter features a clean and quiet Gates Carbon Drive belt, which eliminates the maintenance that comes with a derailleur, and an internally geared Enviolo Trekking hub, which provides a 380 percent gear range. The Embark has 650b wheels, 47mm WTB gumwall tires, full fenders with mudflaps, and integrated lights—meaning you can ride long after the sun sets—or before it rises. A Bosch Active Line Plus mid-drive motor is light and quiet and provides pedal assist up to 20 mph, and the Bosch 400Wh battery has a claimed range of 50 miles. Everything about the Embark frame screams clean, stylish, and organic.
A new European product safety standard EN 15194 will be published in 2009. EN 15194 contains several new requirements for ebikes to be sold in European Union and European Economic Area, including weight and voltage limitations. EN 15194 also defines a specific name for EU approved electrically-assisted cycles, EPAC - "Electrically Pedal Assisted Cycle".
The bicycle's invention has had an enormous effect on society, both in terms of culture and of advancing modern industrial methods. Several components that eventually played a key role in the development of the automobile were initially invented for use in the bicycle, including ball bearings, pneumatic tires, chain-driven sprockets and tension-spoked wheels.
As often preached, eBikes are arguably the most efficient, enjoyable and clean way to travel around the city. Here at Fully Charged, we have an eBike for all, from the eMTBs, to folding electric bikes. But certainly our most popular are urban commuter eBikes. For those bored of playing sardines on the tube, or taking … Continue reading Commuter eBike riding: The Fully Charged Picks
E-bike usage worldwide has experienced rapid growth since 1998. In 2016 there were 210 million electric bikes worldwide used daily. It is estimated that there were roughly 120 million e-bikes in China in early 2010, and sales are expanding rapidly in India, the United States of America, Germany, the Netherlands, and Switzerland. A total of 700,000 e-bikes were sold in Europe in 2010, up from 200,000 in 2007 and 500,000 units in 2009.
A response to an inquiry made to the Mass DOT/RMV indicates that Massachusetts does recognize the federal low speed electric bicycle Federal Law (15 U.S.C. § 2085) and interprets that to mean these ebikes do not require license or registration. However, some of the materials available on the RMV website do not distinguish between "Motorized Bicycle" and low power ebikes. One form, Bicycle Conversion to Motorized Bike, does document the exemption of low power ebikes.
Since 2000, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs) as a separate category, and which require no license to operate. PABs are currently defined as a two- or three-wheeled bicycle equipped with handlebars and operable pedals, an attached electric motor of 500W or less, and a maximum speed capability of 32 km/h from the motor over level ground. Other requirements include a permanently affixed label from the manufacturer in a conspicuous location stating the vehicle is a power-assisted bicycle under the statutory requirements in force at the time of manufacture. All power-assisted bicycles must utilize an electric motor for assisted propulsion.
As the managing editor of Ars Technica, one of my duties is to monitor the daily torrent of news tips and PR emails. The overwhelming majority of them is deleted after a glance, and the news tips and story ideas are passed along to the appropriate writer. Sometimes a product announcement will catch my eye, and I will follow up. Once in a blue moon, I'll say, "please send me one so that I may review it." And that's how I ended up riding an electric bike around the Chicago suburbs for two weeks.
Since 2001, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs). They are currently defined as a two or three wheeled bicycle with an attached electric motor of 500W or less and which is capable of being propelled manually. Furthermore to meet the safety requirements set down by this legislation it must meet the following; when engaged by muscular power it must cease assistance when muscular power ceases or if powered by an accelerator controller cease power when braking and be incapable of providing assistance above 32 km/h and bear a label that is permanently affixed by the manufacturer and appears in a conspicuous location stating the vehicle is a power-assisted bicycle.
Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! 
If you have dynamo-powered bicycle lights, you already own an electric-powered bicycle! Consider: as you pump your legs up and down on the pedals, you make the wheels rotate. A small dynamo (generator) mounted on the rear wheel produces a tiny current of electricity that keeps your back safety lamp lit in the dark. Now suppose you could run this process backward. What if you removed the lamp and replaced it with a large battery. The battery would kick out a steady electric current, driving the dynamo in reverse so that it spun around like an electric motor. As the dynamo/motor turned, it would rotate the tire and make the bike go along without any help from your pedaling. Hey presto: an electric bike! It may sound a bit far-fetched, but this is more or less exactly how electric bikes work.
Eight provinces of Canada allow electric power assisted bicycles. In all eight provinces, e-bikes are limited to 500 W output, and cannot travel faster than 32 km/h (20 mph) on motor power alone on level ground. In Alberta prior to July 1, 2009, the limits were 750 W and 35 km/h (22 mph), but presently match federal legislation. Age restrictions vary in Canada. All require an approved helmet. Regulations may or may not require an interlock to prevent use of power when the rider is not pedaling. Some versions (e.g., if capable of operating without pedaling) of e-bikes require drivers' licenses in some provinces and have age restrictions. Vehicle licenses and liability insurance are not required. Generally, they are considered vehicles (like motorcycles and pedal cycles), so are subject to the same rules of the road as regular bicycles. In some cases, regulatory requirements have been complicated by lobbying in respect of the Segway PT.
Tires vary enormously depending on their intended purpose. Road bicycles use tires 18 to 25 millimeters wide, most often completely smooth, or slick, and inflated to high pressure in order to roll fast on smooth surfaces. Off-road tires are usually between 38 and 64 mm (1.5 and 2.5 in) wide, and have treads for gripping in muddy conditions or metal studs for ice.
There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
In some countries mixed systems, i.e. pedaling and/or using a throttle is legal. In EU countries and Switzerland this is not the case. I.e. you can buy an electric scooter, but this is not considered to be an e-bike in the moped / light scooter category. That kind of hack is probably more difficult, unless the original design has been modified to fit with (s)Pedelec specs. E.g. The Ezee models are of that kind and modifications to revert to the original does not seem to be too difficult...
Built around a heavy-duty alloy frame, the GSD eschews many of the traits of other cargo bikes: long wheelbases, bigger wheels, and especially, an unwieldy ride. Yet it boasts an extensive capacity, nimble handling—even fully loaded, thanks to a short wheelbase and 20-inch wheels—and enduring range in a package not much bigger than most non-cargo e-bikes. The stout frame holds a 250-watt Bosch motor that gives up to 275 percent of your power back to the pedals and reaches 20 mph. The GSD has room for two battery packs, extending the batteries’ combined range to a claimed 150 miles and making the Tern one of the longest-lasting e-bikes on the market. A laundry list of accessories and a (claimed) 396-pound carrying capacity round out the GSD’s status as an epic day-tripper.
In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.
Battery – in combination with the motor, this determines how far you can get before your bike needs a recharge. Some don’t provide adequate support on even gentle hills, while the best will comfortably take the strain as the gradient shoots up. Range also varies, with the best e-bike systems we’ve tested able to take you nearly twice the distance of lesser models.
But the whole is also influenced by the sensory systems which are very different from model to model. E.g. A typical 2013 Panasonic system requires pedalling for optimal support (55/minute?) and has both a pedalling frequency and a speed sensor. You don't get much assistance if you pedal very slowly or very fast. Typically, a rear motor has a force sensor, i.e. you get lots of support fast when you start pedalling in a low gear, i.e. it will "feel" your need for assistance.
But the good times of the stealthy ebike existence will not endure forever. The ebike market is growing steadily and more so, technology is driving performance up and costs down. The market for a green, lifestyle friendly, transportation technology, with GPS, theft ID, cell service and probably skim lattes is alive and driving an emerging market. It is a matter of time before we all must face and respond to the legal demands of the state and local laws. Not to be over obligatory about being legal and duty oriented, but I do call on my fellow ebikers to ride legal, whether ebike, moped or other. Go ahead and build the 1200W ebike of your dreams, but get it insured and licensed if you must. Such compliance will set the precedence for public acceptance of ebikes in general, and build a track record for expansion and mainstreaming of moped-speed ebikes for commuter value driven needs of the future.
I eventually got used to it over time, but at first having both kids behind me made the bike feel like it would sway to or fro perilously. I think it was just too much weight to navigate safely, and would be fine with younger kids that didn’t come close to the 120-pound weight limit for the rear cargo area. Overall I’m still a bit partial to a box-style bike if I’m hauling multiple kids and want to be able to see what they’re doing.
Having spent some quality time with Wing’s e-bike, I understand why so many people are excited about the growing popularity of electric-powered vehicles like bikes and scooters. They take a lot of the work out of getting from point A to point B, while retaining all of the joy. They can give you more confidence when navigating a treacherous city terrain that prioritizes cars over people. And let’s face it: bikes are cool, and always will be.