I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have
In Norway, e-bikes are classified as ordinary bicycles, according to the Vehicle Regulation (kjøretøyforskriften) § 4-1, 5g. Hence, e-bikes are not registered in the Vehicle Registry, and there is no demand for a license to drive them. Still, there are constraints on the bicycle construction. The maximum nominal motor power output can be no more than 250 watts and the maximum performance speed of the vehicle when the engine is running is 25 km per hour (15 mph). A function that reduces motor power when vehicle speed exceeds 25 km per hour is mandatory. However, if the motor is not running, the e-bike, or any other bike, answer only to the constraints of the ordinary speed limits.
October 5, 2009 — Ontario is bringing in some new safety requirements for electric bikes. E-bikes, which can reach a speed of 32 kilometres per hour, are allowed to share the road with cars, pedestrians and other traffic throughout the province. The new rules limit the maximum weight of an e-bike to 120 kilograms, require a maximum braking distance of nine metres and prohibit any modifications to the bike's motor that would create speeds greater than 32 kilometres per hour. Also, riders must be at least 16 years of age, wear approved bicycle or motorcycle helmets and follow the same traffic laws as bicyclists. Municipalities will be able to decide where e-bikes may be used on their streets, bike lanes and trails. E-bikes will not be permitted on 400-series highways, expressways or other areas where bicycles are not allowed. Riding an e-bike under the age of 16 or riding an e-bike without an approved helmet carries fines ranging from $60 to $500. For all other traffic offences, e-bike riders will be subject to the same penalties as cyclists.
An e-bike is identified as a "motor assisted cycle" (MAC) in British Columbia, which differs from electric mopeds and scooters, which are "limited-speed motorcycles." Motor assisted cycles must: have an electric motor of no more than 500 W; have fully operable pedals; not be capable of propelling the device at a speed greater than 32 km/hr [19.9 mph]. The engine must disengage when (a) the operator stops pedaling, (b) an accelerator controller is released, OR (c) a brake is applied. A driver's license, vehicle registration, and insurance are all not required. A bike helmet must be worn.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers. Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
Battery-electric locomotive Battery electric vehicle Cater MetroTrolley Electric aircraft Electric bicycle Pedelec Electric boat Electric bus Battery electric bus Electric car List Electric truck Electric platform truck Electric vehicle Electric motorcycles and scooters Electric kick scooter Gyro flywheel locomotive Hybrid electric vehicle Hybrid train Motorized bicycle Neighborhood Electric Vehicle Plug-in electric vehicle List Plug-in hybrid electric vehicle Solar vehicle Solar car Solar bus
Range is a key consideration with electric bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. The range of an electric bike is usually stated as somewhere between 7 km (uphill on electric power only) to 70 km (minimum assistance) and is highly dependent on whether or not the bike is tested on flat roads or hills. Some manufacturers, such as the Canadian BionX or American E+ (manufactured by Electric Motion Systems), have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging. This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS.
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.
It should be noted that the definition as written does not define the power of the motor in Watts as is conventionally done for electric bicycles but rather in brake horsepower. Thus for an electric bicycle, motor kit, or electric bicycle motor that is not rated by the manufacture in brake horsepower but rather in Watts a conversion must be made in the units a conversion which is not given in the code of the law and thus the court will have to consider a factor of conversion that is not directly encoded in the law. Industry standard conversion for Watts to horsepower for electric motors is 1 horsepower = 746 watts. Acceptance of that conversion factor from industry, however, as interpretation of the law is subject to the process of the courts since it is not defined specifically in the law.
Built around a heavy-duty alloy frame, the GSD eschews many of the traits of other cargo bikes: long wheelbases, bigger wheels, and especially, an unwieldy ride. Yet it boasts an extensive capacity, nimble handling—even fully loaded, thanks to a short wheelbase and 20-inch wheels—and enduring range in a package not much bigger than most non-cargo e-bikes. The stout frame holds a 250-watt Bosch motor that gives up to 275 percent of your power back to the pedals and reaches 20 mph. The GSD has room for two battery packs, extending the batteries’ combined range to a claimed 150 miles and making the Tern one of the longest-lasting e-bikes on the market. A laundry list of accessories and a (claimed) 396-pound carrying capacity round out the GSD’s status as an epic day-tripper.
I purchased version 2.0 of this device and the manufacturer has been listening to comments from users and making running changes such as the three speeds and the rear suspension. I am an XL size user (6'2", 230lbs) and recently returned from a 26 day cruise around Europe. I rode this little scooter on cobblestones, miles and miles through the Vatican, inside ancient cities and all over the streets of San Juan upon our return stateside. There was only one time it was less than ideal and that was going uphill, on slick tile that was wet from a drizzle. It still make it, just had to lean way forward to get weight on the front wheel.
Battery – in combination with the motor, this determines how far you can get before your bike needs a recharge. Some don’t provide adequate support on even gentle hills, while the best will comfortably take the strain as the gradient shoots up. Range also varies, with the best e-bike systems we’ve tested able to take you nearly twice the distance of lesser models.
On a trip to Palo Alto last year, we had the chance to ride Specialized’s pedal-assisted Turbo Vado and the model is still our favorite ebike on the market. Utilizing a 350-watt motor and 604-watt-hour lithium-ion battery, the Turbo Vado is capable of traveling a whopping 80 miles on a single charge, which should be more than enough for any daily commute with plenty of miles left over.
The Ohio Revised Code 4511.01  distinguishes motorized bicycles and mopeds from motorcycles or scooters by describing them as "...any vehicle having either two tandem wheels or one wheel in the front and two wheels in the rear, that is capable of being pedaled and is equipped with a helper motor of not more than fifty cubic centimeters piston displacement that produces no more than one brake horsepower and is capable of propelling the vehicle at a speed of no greater than twenty miles per hour on a level surface." One brake horsepower converts to 0.75 kW, or (rounded) 750W. Thus, a bicycle with an electric helper motor operating under 750W, and not propelling the bicycle over 20 mph, does not qualify to be registered under Ohio state law. Local jurisdictions may have other regulations.
In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.
Some US companies, notably in the tech sector, are developing both innovative cycle designs and cycle-friendliness in the workplace. Foursquare, whose CEO Dennis Crowley "pedaled to pitch meetings ... [when he] was raising money from venture capitalists" on a two-wheeler, chose a new location for its New York headquarters "based on where biking would be easy". Parking in the office was also integral to HQ planning. Mitchell Moss, who runs the Rudin Center for Transportation Policy & Management at New York University, said in 2012: "Biking has become the mode of choice for the educated high tech worker".
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885. However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.
At the top end, the 20mph speed limit isn't an absolute, like the speed of light. It's just the most you'll get from the motor. I was able to get it up to 28mph on a flat road (there are no other roads where I live) in Turbo mode and 8th gear, but it took hard work to get there and maintain the speed. The easiest comparison is my mountain bike, where I've hit 23mph on that same stretch of road—and that took a heck of a lot of effort. Exactly how much effort does it take to ride? I have a 15-mile route that I ride on both my mountain bike and cyclecross bike. According to my Apple Watch, I generally burn around 1,400 or so calories on a brisk ride. I'll probably average around 13mph or so on my Marlin and between 16 and 17.5mph on my XO2. I averaged 14.9mph and burned a hair over 1,000 calories with the Bulls Cross E8.
Speaking of which, if you're used to non-electric cycles, be aware that e-bikes are heavy and capped at 25kph or 15.5mph. In many cases, that means the bike starts to feel like its actively fighting against you, if you try to push the speed higher than that by pedalling. That's especially true with heavier bikes, for obvious reasons, and can take a while to get used to.
The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop. They were among the early shops to embrace family friendly cargo bikes and appreciated the role that electric would play in making cycling more broadly appealing.
E-Bikes are the perfect way to ride across any city: stress-free, easy and fast travel, fun exercise, riding in style and ability to carry heavier loads than a normal bike. Practicing what we preach, this Valentine’s Volt partnered with leading London florist Rebel Rebel to deliver flowers all across London. Every hour on the hour 1 lucky person received a beautiful bouquet for free, just because we wanted to share the love!
Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.
Great question… a real world situation from someone doing their best to follow the law but also be realistic about time/distance. What follows is my opinion on the matter based on lots of electric bike riding experience, this is not legal advice. You can probably ride with electric assist across the dirt way with no issues and avoid any negative response that might arise as long as you’re polite to other cyclists and pedestrians and pedal along without going too fast. If someone called you out about it you could easily hop off, walk your bike and explain that you use the assist to help make your commute possible or possibly, like me, you have a knee injury and it’s difficult to pedal through softer terrain like gravel. Another different approach might be to shut the bike off completely before entering the gravel section, you could even take the battery off and put it in a backpack or as mentioned earlier… just walk the bike. Imagine if you had a motorized dirt bike and were just pushing it along a sidewalk… this kind of vehicle definitely is not allowed on sidewalks or most gravel paths like the one you’re describing but if you were escorting it carefully, you’d be honoring the spirit of the law and if an officer or pedestrian jumped out and started questioning you about your “motorized vehicle” it is my feeling that a genuine explanation and apology or request for guidance would go very well. I personally have never had issues riding electric bikes in part because I am thoughtful about how I use them. I do occasionally switch them off and sometimes I get off and walk. I have asked police in many cities across the US what they thought about ebikes and in every case I have received positive interest and support with guidance to ride safe with a helmet and follow traffic laws in the street. I hope this helps and I wish you well, it’s nice that you care enough to ask and I hope you’re treated well by others out on the road. The flip side of this response is that I have been harassed, yelled at and even swerved at by automobiles when riding bicycles and electric bikes. This usually happens in the evening after work lets out when traffic is heavy and I’m riding on the shoulder or in the street (where marked to do so) and I believe it has to do with territory, testosterone and socio-economic standing more so than laws or anything like that.
Different gears and ranges of gears are appropriate for different people and styles of cycling. Multi-speed bicycles allow gear selection to suit the circumstances: a cyclist could use a high gear when cycling downhill, a medium gear when cycling on a flat road, and a low gear when cycling uphill. In a lower gear every turn of the pedals leads to fewer rotations of the rear wheel. This allows the energy required to move the same distance to be distributed over more pedal turns, reducing fatigue when riding uphill, with a heavy load, or against strong winds. A higher gear allows a cyclist to make fewer pedal turns to maintain a given speed, but with more effort per turn of the pedals.
In principle, you would use about 100W (your own energy) for moderate pedalling at 22km/h. If you select 300% assistance (high), that will add another 300W and you can pedal almost twice as fast, i.e. about 27km/h (you will encounter increasing resistance from wind). Therefore, if you got a 400Wh battery, you got a range of about 37km at 37km/h. If go more slowly and use less support (200%), then you can drive further, e.g. 60km with a 400Wh battery. (Read more in die Die Schnellen im Vergleich)
The bicycle is extraordinarily efficient in both biological and mechanical terms. The bicycle is the most efficient human-powered means of transportation in terms of energy a person must expend to travel a given distance. From a mechanical viewpoint, up to 99% of the energy delivered by the rider into the pedals is transmitted to the wheels, although the use of gearing mechanisms may reduce this by 10–15%. In terms of the ratio of cargo weight a bicycle can carry to total weight, it is also an efficient means of cargo transportation.
The Footloose has no chain, however -- it's entirely electrically driven. It takes very little effort to get to your destination, meaning you arrive at work without having broken a sweat. The downside is that when you run out of power, you're not going anywhere. And pedalling from a standstill, waiting for the motor to kick in, is an odd sensation that takes some getting used to.