Range is a key consideration with electric bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. The range of an electric bike is usually stated as somewhere between 7 km (uphill on electric power only) to 70 km (minimum assistance) and is highly dependent on whether or not the bike is tested on flat roads or hills.[14] Some manufacturers, such as the Canadian BionX or American E+ (manufactured by Electric Motion Systems), have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[15] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS.
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.

The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.


Whether squeezing onto the 4 train or pedaling through Lower Manhattan, I notice a few curious glances at the bike with the big battery in the center of the frame. This is not surprising; e-bikes are huge practically everywhere but the US. According to the latest figures from the Confederation of the European Bicycle Industry, e-bike growth in the UK is up from 40,000 units in 2016 to 63,000 in 2017.


The $3,099 MSRP is a bit daunting if you've not shopped for high-end bikes before, but it compares favorably with, say, Trek's electric bike lineup. That said, you can get a solid urban/commuter bike without a motor for well under $1,000. You can even score an e-bike for under a grand, but you'll likely be looking at a battery range of less than 40 miles, along with lower-quality components.
Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.[5]
The first regularly produced device resembling the modern bicycle was unveiled in 1818. It was called the Dandy Horse. The two-wheeled ride-on Dandy Horse was the brainchild of German inventor Baron Karl Drais, and it featured a handle bar, a padded seat, and two inline wheels of nearly equal size. What it did not feature were pedals; this was a "running machine," thus its name in German, Laufmachine. The Dandy Horse saw only a flicker of popularity, and was largely an historical footnote within a handful of years, though its design is nearly mimicked in the child's balance bike of today.
Like most electric bikes, the Rad Wagon is also fairly heavy, weighing 72 pounds. The last drawback is that it comes in only one frame size (which I imagine helps to keep costs lower) that fits rider heights between 5 foot 2 inches and 6 foot 2 inches. My 6 foot 4 husband, however, can ride the bike just fine, so there’s some wiggle room to this range.
Bicycle shall mean (1) every device propelled solely by human power, upon which any person may ride, and having two tandem wheels either of which is more than fourteen inches in diameter or (2) a device with two or three wheels, fully operative pedals for propulsion by human power, and an electric motor with a capacity not exceeding seven hundred fifty watts which produces no more than one brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than twenty miles per hour on level ground.
The Christmas day is coming soon, since I receive the bike, it's about a week, and I am satisfied with it! just as advertised, very powerful and good design. the most important point is that once the battery is FULL CHARGE, how far it can reach up to. I have a funny test, in the normal road(not in the dramatic slope or uphill), it can goes almost 44 miles. That is what I give 5 star for this bike! very powerful with reasonable price!

“Changes in production and consumption patterns are a crucial element of the sustainability agenda. Communication between product developers and users, and user integration in product development, can serve as a means for organizational as well as individual learning processes, resulting in sustainable product development. [...] Improved methods, such as INNOCOPE (innovating through consumer-integrated product development), tested in this study with a cycle manufacturer and resulting in a new product, a pedelec, are needed for effective communication, activating consumers and enabling them to promote sustainability goals. Through co-operative product development processes key factors facilitating and obstructing the adoption of sustainable innovations may be identified. Such processes can enhance the emergence and diffusion of sustainable product innovations and different forms and bodies of knowledge can be combined. Integrating users' contextual everyday knowledge of the product with the technical knowledge of companies may lead to mutual learning, technical innovations and changes in consumer behaviour.” (Hoffmann, 2007).
The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.
Indian law requires that all electric vehicles have ARAI[50] approval. Vehicles with below 250W and speed less than 30 km/h, do not require certification- hence not following full testing process, but needs to get exemption report from ARAI. Whereas more powerful vehicles need to go through a full testing process following CMVR rules. This can take time and cost money but assures safe and reliable design for Electric Vehicles. These regulations are not promulgated by the Regional Transport offices, and riders are not required to obtain a licence to drive, to carry insurance, or to wear a helmet.
European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.
Solar Shunt firmware: With this firmware the Cycle Analyst can use the auxilliary input as a second current sensor for measuring and showing the solar amps and watts. You can not only see in realtime how much solar power is coming into the pack, you also get combined statistics such as the %solar recharge and the net wh/km mileage taking into account the solar input for the day. This is the ideal instrument for looking at solar ebike performance, consolodating all measurements in a single device.
Fast and fun on the trail, the SDURO HardNine handles rough terrain with ease, while its large tires roll over most obstacles without missing a beat. The pedal assist makes for quick, energy-saving climbing and the bike descends surprisingly well, too. Its front suspension provides a nice level of cushion on bumpy trails and while we missed having a full-suspension on this model, that would have added additional weight and costs.
But unlike other battery mounted controllers, the Baserunner also stands on its own too. If you upgrade to a different battery model in the future that doesn't fit the cradle, simply remove the Baserunner from the base and use it as a miniature stand alone controller with your new battery pack. That's Grin thinking about your future options for you.
How do the State Laws relate to the 2001 Federal Law? This is a difficult question to answer and know how they apply to you individually. From the Federal Law, one would hope that your purchased ebike is simply classified as a bicycle, with all the rights and privileges allotted to a normal cyclist. However, State Laws are confusing because they may be more restrictive in parts and add other requirements. About 30 U.S. states still have confusing regulations around them. Either the bikes are technically classified as mopeds or motor vehicles, or they have equipment, licensing or registration requirements that cause problems for riders. Thanks to the People-For-Bikes/Bicycle Product Suppliers Association (BPSA) partnership with local advocacy groups, they have been able to make the case for streamlining state regulations so that e-bikes are essentially treated like regular bicycles.4
Bicycle brakes may be rim brakes, in which friction pads are compressed against the wheel rims; hub brakes, where the mechanism is contained within the wheel hub, or disc brakes, where pads act on a rotor attached to the hub. Most road bicycles use rim brakes, but some use disk brakes.[49] Disc brakes are more common for mountain bikes, tandems and recumbent bicycles than on other types of bicycles, due to their increased power, coupled with an increased weight and complexity.[50]
Let’s face it – Commuting can be a nightmare. Seemingly infinite price hikes, delays to trains, crammed tubes and congested roads dominate the ways of getting to work. The commuter misery is real. But, what if you could transform this part of the day from a chore to a pleasure? Enter the eBike. The clean, … Continue reading Why an eBike is so good for commuting
The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.
The Super Commuter is very aptly named. The 350w Bosch motor will help you sustain speeds of up to 28mph, and the burly, 2.4-inch wide, Schwalbe Super Moto-X 650b tires will keep you secure on even the roughest city streets, and Shimano Deore hydraulic brakes provide ample stopping power. Fenders provide welcome protection from road spray so you arrive at your destination fresh, integrated lights are critical for post-sunset riding, and a side-view mirror hanging on the left side of the handlebar gives a great view of traffic around you. After all, you can ride at the speed of urban traffic on the Super Commuter.
Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).
Bicycles helped create, or enhance, new kinds of businesses, such as bicycle messengers,[92] traveling seamstresses,[93] riding academies,[94] and racing rinks.[95][94] Their board tracks were later adapted to early motorcycle and automobile racing. There were a variety of new inventions, such as spoke tighteners,[96] and specialized lights,[91][96] socks and shoes,[97] and even cameras, such as the Eastman Company's Poco.[98] Probably the best known and most widely used of these inventions, adopted well beyond cycling, is Charles Bennett's Bike Web, which came to be called the jock strap.[99]

A human traveling on a bicycle at low to medium speeds of around 16–24 km/h (10–15 mph) uses only the power required to walk. Air drag, which is proportional to the square of speed, requires dramatically higher power outputs as speeds increase. If the rider is sitting upright, the rider's body creates about 75% of the total drag of the bicycle/rider combination. Drag can be reduced by seating the rider in a more aerodynamically streamlined position. Drag can also be reduced by covering the bicycle with an aerodynamic fairing. The fastest recorded unpaced speed on a flat surface is 144.18 km/h (89.59 mph)[41]

In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris.[22] The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind).[23] It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.[24]
This is a virtual hello to all the people who came by our booth last weekend at the BC Bike Show and are just now visiting our webpage for the first time. We had a great time and were delighted to see how much this event has grown recently. (And to those who lament that the bike show is now totally taken over by ebikes, well it's been over 15 years now that we've been trying to tell you all this day was coming!)
Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.[16]
During nighttime operation, the bicycle must be equipped with a front headlamp, a rear-facing red reflector, and reflectors on the front and rear of pedals, and the bicycle or rider must have reflective surfaces on each side. Minn. Stat. §169.222, subd. 6. An electric-assisted bicycle can be equipped with a front-facing headlamp that emits a flashing white light, a rear-facing lamp that has a flashing red light, or both. The bicycle can carry studded tires designed for traction (such as in snowy or icy conditions).
In the Netherlands all train stations offer free bicycle parking, or a more secure parking place for a small fee, with the larger stations also offering bicycle repair shops. Cycling is so popular that the parking capacity may be exceeded, while in some places such as Delft the capacity is usually exceeded.[64] In Trondheim in Norway, the Trampe bicycle lift has been developed to encourage cyclists by giving assistance on a steep hill. Buses in many cities have bicycle carriers mounted on the front.

Electric bikes vary widely in price, anywhere from $999 to $2000+, so you’ll have to determine how important certain features are to the overall cost. (However, we made a list of electric bikes under $1.000 here.)The battery used to power an electric bike motor is a key factor in how expensive a particular bike is. In general, the more miles a battery can provide, the more expensive it will be, so it’s important to consider the type of riding you plan on doing. If you know you’ll be using predominantly motor-generated power, then paying a bit more for a battery with a longer range is probably a good idea. Alongside with a good quality battery, motor is the most expensive part of an electric bike. Most standard electric bike motors come with a power rating of 250W, and the industry standard in the US is 500W. Maximum power of the motor you can legally use in the US is 750W. The non-electric components used on an electric bike are almost the same with those used on the conventional bicycles. The quality of the components used will affect the maintenance costs of your electric bike down the road, and more quality components mean higher upfront cost. Lastly, there is the frame. Since the frame is basically the skeleton of your electric bike, it’s wise to select a good material that will be the optimum combination of weight and durability.
I was hesitant to buy this battery at first due to the minimal amount of review feedback and poor English Grammer in the description. You never know. But, I ended up being very happy with it. Out of all the ebike components I ordered, this battery took the longest by far to get to me, about 11 days to reach me in North Central Florida. However, I believe that's because they ship from China which would also explain the poor grammar in the description. When you think about it, 11 days all the way from China is not bad. Considering the great price and inclusion of the rear rack, it really was worth the wait. I put it on a fat tire mongoose dolomite equipped with a 48v 1000w front hub motor. It was a very heavy bike to begin with, and my thinking was that having the motor in
And let’s not forget the economic advantages of owning an e-bike. The annual cost of running a new family car is, on average, about $9,000 per year. Running an electric bike costs around $400 per year. And while filling a gas tank costs around $30, recharging an electric bike battery costs only about 50 cents. A tank of gas may get you further, but not 60 times further!

Having spent some quality time with Wing’s e-bike, I understand why so many people are excited about the growing popularity of electric-powered vehicles like bikes and scooters. They take a lot of the work out of getting from point A to point B, while retaining all of the joy. They can give you more confidence when navigating a treacherous city terrain that prioritizes cars over people. And let’s face it: bikes are cool, and always will be.


Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).
FuroSystems is a London-based startup that is launching two new full carbon fiber electric bikes, a folding e-bike and a mountain e-bike. FuroSystems’ ambition was to design very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and to sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.

Electric powered bicycles slower than 20 km/h without pedaling are legally recognized as a non-mechanically operated vehicle in China.[32] According to "TECHNOLOGY WATCH", this should help promote its widespread use.[33] Electric bicycles were banned in some areas of Beijing from August 2002 to January 2006 due to concerns over environmental, safety and city image issues. Beijing has re-allowed use of approved electric bicycles as of January 4, 2006.[34] Some cities in China still ban electric bikes.
My homeowners (State Farm) covers bikes , but assumes $500 per bike. They will add the bikes as personal property, but the premium is excessive (about $300/year per bike, and we have four bikes). I did increase our personal umbrella liability coverage, and it covers us if family members any sort of accident on our e-bikes that injures us or others or others' property, though only covers $500 each for our own bikes (under the homeowners coverage). It was not very expensive to increase the umbrella policy (as it resulted also in a reduced rate on our car insurance).
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[65]
The frame itself incorporates a series of mounts allowing you to easily trick-out the Road E+1 with a rack, fenders, or panniers to more aptly meet your touring requirements. Again, most touring purists will certainly scoff at the mere notion of pedal-assistance, however, individuals looking for more of a guided tour and less of a tour de force will swoon over the Road E+1.
There are generally two types of e-bike: throttle and pedal-assist. Throttle e-bikes, common among food delivery workers, don’t require any pedaling, just a twist of the handlebar to get moving. Wing’s e-bike is pedal-assist. The bike’s battery provides a boost while you pedal — up to 20 mph — but if you stop pedaling, the bike slows just like a regular bike.
Electric bikes are here in a big way. Liberated from some of the normal constraints of standard bike design like weight and gearing, e-bike design has exploded; if you can imagine it, someone has built it. From cargo bikes to city bikes, messenger bikes to mountain bikes, road bikes, folding bikes, and even beach cruisers, there is something for everyone. The beauty of e-bikes is that they make the joy of cycling accessible to so many people in so many ways.

The handlebars connect to the stem that connects to the fork that connects to the front wheel, and the whole assembly connects to the bike and rotates about the steering axis via the headset bearings. Three styles of handlebar are common. Upright handlebars, the norm in Europe and elsewhere until the 1970s, curve gently back toward the rider, offering a natural grip and comfortable upright position. Drop handlebars "drop" as they curve forward and down, offering the cyclist best braking power from a more aerodynamic "crouched" position, as well as more upright positions in which the hands grip the brake lever mounts, the forward curves, or the upper flat sections for increasingly upright postures. Mountain bikes generally feature a 'straight handlebar' or 'riser bar' with varying degrees of sweep backwards and centimeters rise upwards, as well as wider widths which can provide better handling due to increased leverage against the wheel.


Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).
×