State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour. Subchapter J of Publication 45 spells out the vehicle requirements in full.
Bicycle shall mean (1) every device propelled solely by human power, upon which any person may ride, and having two tandem wheels either of which is more than fourteen inches in diameter or (2) a device with two or three wheels, fully operative pedals for propulsion by human power, and an electric motor with a capacity not exceeding seven hundred fifty watts which produces no more than one brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than twenty miles per hour on level ground.
Federal law in the United States states that an electric bicycle must have a top speed under 20 mph and a motor which produces less than 750 watts/1 hp. They are not considered motor vehicles by the federal government and are subject to the same consumer safety laws as unassisted bicycles. Their legality on public roads is under state jurisdiction, and varies. See the main Electric bicycle laws article for details on the law in individual states.
Electric motorized bicycles can be power-on-demand, where the motor is activated by a handlebar mounted throttle, and/or a pedelec (from pedal electric), also known as electric assist, where the electric motor is regulated by pedaling. These have a sensor to detect the pedaling speed, the pedaling force, or both. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. Most controllers also provide for manual adjustment.
OK, here we go. This electric scooter is also known as the DYU D1 over-seas, if you want to research it a little more, google that instead of Ancheer. This little thing is great. Once you put ten miles, or 16 kilometers on the odometer, the limiter turns off and this thing will hit in the ballpark of 20 mph! (I'm light so I've done 22 on a flat plane.) It has enough torque to go up hills, has functioning headlights and a brake-light, there's two apps you can download on the app store that will allow you to lock, change the speed settings, and see a digital speedometer of the bike. Very impressive in my opinion, even the handlebars fold over to make it easier to carry. The bike does not feel cheap, that outer tubular frame you're seeing is real metal. I'm 6' tall and I
However, laws and terminology are diverse. Some countries have national regulations but leave the legality of road use for states and provinces to decide. Municipal laws and restrictions add further complications. Systems of classification and nomenclature also vary. Jurisdictions may address "power-assisted bicycle" (Canada) or "power-assisted cycle" (United Kingdom) or "electric pedal-assisted cycles" (European Union) or simply "electric bicycles". Some classify pedelecs as distinct from other bikes using electric power. Thus, the same hardware may be subject to many different classifications and regulations.
How do the State Laws relate to the 2001 Federal Law? This is a difficult question to answer and know how they apply to you individually. From the Federal Law, one would hope that your purchased ebike is simply classified as a bicycle, with all the rights and privileges allotted to a normal cyclist. However, State Laws are confusing because they may be more restrictive in parts and add other requirements. About 30 U.S. states still have confusing regulations around them. Either the bikes are technically classified as mopeds or motor vehicles, or they have equipment, licensing or registration requirements that cause problems for riders. Thanks to the People-For-Bikes/Bicycle Product Suppliers Association (BPSA) partnership with local advocacy groups, they have been able to make the case for streamlining state regulations so that e-bikes are essentially treated like regular bicycles.4
“Changes in production and consumption patterns are a crucial element of the sustainability agenda. Communication between product developers and users, and user integration in product development, can serve as a means for organizational as well as individual learning processes, resulting in sustainable product development. [...] Improved methods, such as INNOCOPE (innovating through consumer-integrated product development), tested in this study with a cycle manufacturer and resulting in a new product, a pedelec, are needed for effective communication, activating consumers and enabling them to promote sustainability goals. Through co-operative product development processes key factors facilitating and obstructing the adoption of sustainable innovations may be identified. Such processes can enhance the emergence and diffusion of sustainable product innovations and different forms and bodies of knowledge can be combined. Integrating users' contextual everyday knowledge of the product with the technical knowledge of companies may lead to mutual learning, technical innovations and changes in consumer behaviour.” (Hoffmann, 2007).
Around the turn of the 20th century, bicycles reduced crowding in inner-city tenements by allowing workers to commute from more spacious dwellings in the suburbs. They also reduced dependence on horses. Bicycles allowed people to travel for leisure into the country, since bicycles were three times as energy efficient as walking and three to four times as fast.
This electric bike received a five star. The assembly was pretty simple. I ordered a set of lights and a over rear tire carrier rack from amazon that took longer to install than it took too assemble the bike.This is a solid built by that is attractive and worthy of this price point. The build quality of this bike was very good. So far I've done a few test and it runs perfect. I've put on 50+ miles on this bike and have used it on flat ground, dirt roads, rocky trails and grassy fields. The bike runs quicker than what I expected from a small 250 W hub motor. I really like it in almost every way.
This Class 3 (28 mph), utilitarian, road e-bike is smooth and torquey thanks to its Bosch Performance Speed motor. With a drop bar and traditional road-bike position and handling, the CrossRip+ is more suited to longer rides on mixed terrain than navigating congested city streets. It comes with a rear rack—for mounting bags, not for attaching cargo directly—full fenders, a kickstand, and integrated front and rear lights (which are powered by a Bosch 500Wh battery). It features a SRAM Force 1x11 drivetrain, hydraulic disc brakes, and wide 700x38mm tires.
Not all e-bikes take the form of conventional push-bikes with an incorporated motor, such as the Cytronex bicycles which use a small battery disguised as a water bottle. Some are designed to take the appearance of low capacity motorcycles, but smaller in size and consisting of an electric motor rather than a petrol engine. For example, the Sakura e-bike incorporates a 200 W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one.
Equipped with a powerful motor, a portable Li-ion Battery, and all the other magic that goes into building a LightSpeed Electric Bicycle… It’s lighter than it looks, strong yet agile, and feels like flying.This beast is truly larger than life. To bring it home, you need a special invite. Follow this space for more information on how to get invited.
Step-throughs were popular partly for practical reasons and partly for social mores of the day. For most of the history of bicycles' popularity women have worn long skirts, and the lower frame accommodated these better than the top-tube. Furthermore, it was considered "unladylike" for women to open their legs to mount and dismount—in more conservative times women who rode bicycles at all were vilified as immoral or immodest. These practices were akin to the older practice of riding horse sidesaddle.
Historically, women's bicycle frames had a top tube that connected in the middle of the seat tube instead of the top, resulting in a lower standover height at the expense of compromised structural integrity, since this places a strong bending load in the seat tube, and bicycle frame members are typically weak in bending. This design, referred to as a step-through frame or as an open frame, allows the rider to mount and dismount in a dignified way while wearing a skirt or dress. While some women's bicycles continue to use this frame style, there is also a variation, the mixte, which splits the top tube laterally into two thinner top tubes that bypass the seat tube on each side and connect to the rear fork ends. The ease of stepping through is also appreciated by those with limited flexibility or other joint problems. Because of its persistent image as a "women's" bicycle, step-through frames are not common for larger frames.
We'll start this off with the latest two Customer Profile videos. In the first one we follow up from the well received Leigh Cross video with a look at his son, Tig Cross. Tig's been refining an original bike concept combining the best parts of an ebike, scooter, and velomobile, and showcases the merits of an electric generator for the human drivertrain.
The second type of electric bike is a much smaller, often foldable unit designed for convenient urban (or suburban) commuting and for easy storage in minimal space. These compact electric bikes are perfect for trips of a few miles, and many are small and lightweight enough to be carried onto trains or buses, allowing their rider to make use of multiple types of transportation in a single trip, and to store their bike in a closet or even under a desk at work, at school, or at home.
We spent 45 hours on research, videography, and editing, to review the top choices for this wiki. With rechargeable, battery-powered pedaling assistance, electric bicycles offer an increasingly viable alternative to fossil-fueled commuting, and e-bikes enable riders of various abilities to extend their cycling range. But the street legality of these hybrid machines remains a contentious issue, so be sure to check current state and local laws governing their operation before you hit the road. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best electric bike on Amazon.
Chart: Electric bicycles are rapidly becoming popular. This chart shows the growth in sales of what the manufacturers refer to as "electric power-assisted cycles (EPACs)" in European countries over the last decade. Over 1.6 million electric bikes were sold in Europe in 2016 alone, which is about 7 percent of total European bicycle sales. What this chart doesn't reveal is that the bikes are much more popular in some countries than others: four countries accounted for 70 percent of all the sales (Germany, 36 percent; the Netherlands, 16 percent; Belgium, 10 percent; and France 8 percent). Data sourced from the report "European Bicycle Market: 2017", courtesy of CONEBI (Confederation of the European Bicycle Industry). These are the newest figures available at the time this article was last updated (September 2018).
Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.
Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! 
Alberta identifies e-bikes as "power bicycles" and is consistent with the federal definition of "power-assisted bicycle" in MVSR CRC, c 1038 s 2. Motor output must not exceed 500 W (0.671 hp) and e-bikes cannot travel faster than 32 km/h (20 mph). Fully operable pedals are required. No driver's license, vehicle insurance, or vehicle registration is required. Operators must be 12 years of age or older. All operators are required to wear a motorcycle helmet meeting the standards set in AR 122/2009 s 112(2). A passenger is permitted only if the e-bike is equipped with a seat designated for that passenger.
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
Would an e-bike that used a trailing generator to power the electric motor still be considered an e-bike? The purpose of the generator is allow greater distances to be traveled and all day riding. The gen-set that I am looking at uses a 49 cc gas engine with a 12 volt generator, this would be from the ground up build using a 1 hp electric motor. This seems to stay within the state laws of AZ. where I reside. Thanks for your thoughts.
Electric bicycles are considered as "bicycles" under Montana law as the law defines bicycles in a two part definition where the first part of the definition describes a conventional bicycle propelled solely by human power and the second part of the definition describes a bicycle equipped with an independent power source for propulsion in addition to foot pedals to permit muscular propulsion. (Montana Code 61-8-102).
Some countries require child and/or adult cyclists to wear helmets, as this may protect riders from head trauma. Countries which require adult cyclists to wear helmets include Spain, New Zealand and Australia. Mandatory helmet wearing is one of the most controversial topics in the cycling world, with proponents arguing that it reduces head injuries and thus is an acceptable requirement, while opponents argue that by making cycling seem more dangerous and cumbersome, it reduces cyclist numbers on the streets, creating an overall negative health effect (fewer people cycling for their own health, and the remaining cyclists being more exposed through a reversed safety in numbers effect).
If you need an ebike that can provide a full-on mountain bike experience, but you are also on a limited budget, this bike is an excellent choice for you. We doubt you can find a double suspension bike, jam-packed with features for a better price. Large wheels and low-rise handlebars provide more control and easier ride, but the powerful 500W brushless motor attached directly to the rear wheel hub will give you plenty of “umph”.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h). An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.. The legislation enacting this amendment to the CPSC is also known as HR 727.
Some components, which are often optional accessories on sports bicycles, are standard features on utility bicycles to enhance their usefulness, comfort, safety and visibility. Mudguards, or fenders, protect the cyclist and moving parts from spray when riding through wet areas and chainguards protect clothes from oil on the chain while preventing clothing from being caught between the chain and crankset teeth. Kick stands keep bicycles upright when parked, and bike locks deter theft. Front-mounted baskets, front or rear luggage carriers or racks, and panniers mounted above either or both wheels can be used to carry equipment or cargo. Pegs can be fastened to one, or both of the wheel hubs to either help the rider perform certain tricks, or allow a place for extra riders to stand, or rest. Parents sometimes add rear-mounted child seats, an auxiliary saddle fitted to the crossbar, or both to transport children. Training wheels are sometimes used when learning to ride.
Legislative changes in 2012 significantly altered the classification and regulatory structure for e-bikes. The general effect was to establish electric-assisted bicycles as a subset of bicycles and regulate e-bikes in roughly the same manner as bicycles instead of other motorized devices with two (or three) wheels. Laws 2012, ch. 287, art. 3, §§ 15-17, 21, 23-26, 30, 32-33, and 41. The 2012 Legislature also modified and clarified regulation of e-bikes on bike paths and trails. Laws 2012, ch. 287, art. 4, §§ 1-4, 20.
The body is made from light and durable aluminum. The handlebar comes with simple controls to let you accelerate, brake, monitor battery life, operate headlights and of course…sound the horn. There’s even an USB point that will let you charge your iPhone or Android on the go. The bike can reach a top speed of 10mph. Feel the wind in your hair as you zoom up and down hills and past all that city traffic…
For many ebike owners, doing their ebike thing usually becomes more than a hobby and good exercise on the weekend with the riding club. It becomes a lifestyle, a utility machine, a darn fun piece of technology on two wheels. As the industry grows and becomes more popular, these unique bikes will be a daily part of many lives and mold into the framework of legal society.
Thanks for your excellent article. I’ve been riding ebike for about 16 years. My first electric bike was a Meridian pedal assist bike. I just up graded to a new bike. I’m 73, so I wanted a pedal assist bike that had a throttle. I researched for several months and bought what I think is the best bike for the money. It’s a Rad Rover 2017 fat bike. It has a 750 watt mother with a 48 volt 11.6 amp battery. It’s a fantastic bike, that is a lot of fun to ride. You might want to check it out and add it to your list of bikes. Rad Rover also make a city commuter bike, a cargo bike and a folding bike. You can’t beat their price for a quality bike. Thanks again for both of your articles. They were very informative.
In some countries mixed systems, i.e. pedaling and/or using a throttle is legal. In EU countries and Switzerland this is not the case. I.e. you can buy an electric scooter, but this is not considered to be an e-bike in the moped / light scooter category. That kind of hack is probably more difficult, unless the original design has been modified to fit with (s)Pedelec specs. E.g. The Ezee models are of that kind and modifications to revert to the original does not seem to be too difficult...
Some power-on-demand only e-bikes can hardly be confused with, let alone categorised as, bicycles. For example, the Noped is a term used by the Ministry of Transportation of Ontario for e-bikes which do not have pedals or in which the pedals have been removed from their motorised bicycle. These are better categorised as electric mopeds or electric motorcycles.
Most European bike rules are tight and restrictive. Right now the California state ebike rules in AB 1096 provide the clearest and cleanest format, and they support ebike riding. No other U.S. regulations come close. The big brand ebikes (Giant, Specialized, Trek) are selling bikes that fit within European rules (250w-300w motors). This gives them economies of scale.
In Norway, e-bikes are classified as ordinary bicycles, according to the Vehicle Regulation (kjøretøyforskriften) § 4-1, 5g. Hence, e-bikes are not registered in the Vehicle Registry, and there is no demand for a license to drive them. Still, there are constraints on the bicycle construction. The maximum nominal motor power output can be no more than 250 watts and the maximum performance speed of the vehicle when the engine is running is 25 km per hour (15 mph). A function that reduces motor power when vehicle speed exceeds 25 km per hour is mandatory. However, if the motor is not running, the e-bike, or any other bike, answer only to the constraints of the ordinary speed limits.